Skip to content
Transport Fever 3 ToolsUnofficial fan toolkit
A Transport Fever 3 cargo station: a red shunting engine and a row of wagons loaded with green crates under a long platform roof, with factory buildings and silos behind

Guide

Transport Fever 3 Full Load (Any) vs (All) and Unload Percentages

Open the unload calculator

Full load (any) lets a vehicle go as soon as one of its cargo types reaches its target, while Full load (all) keeps it at the stop until the whole vehicle is full. With either one, the vehicle still pulls out when Max. Stop Time runs out, full or not. To make it wait as long as it takes, slide Max. Stop Time all the way to the right, until it reads ---.

Last updated Game version: Release version

Make a train wait until it is full

  1. Open the line in the line manager and click the stop where the cargo is picked up.
  2. Pick the cargo the train should take on there and set its percentage: 100% for a full train.
  3. Under Departure Configuration, choose Full load (all). For a mixed train that should go once any one of its cargo types is full, choose Full load (any) instead.
  4. Slide Max. Stop Time all the way to the right, until it shows ---. The train now stays until it is full.

With --- there is no clock at all, so the vehicle leaves only once it is full. If its cargo never comes, it keeps waiting. A stop where nothing arrives is covered in the industry not producing guide.

Load if available vs Full load (any) vs Full load (all)

The three icons under Departure Configuration set what a vehicle waits for before it departs. How they differ depends on the kind of vehicle:

Departure modeTrains and shipsEvery other vehicle
Load if availableTakes whatever compatible cargo is waiting, without holding out for a full load.The same: whatever compatible cargo is there.
Full load (any)Holds until one cargo type is fully loaded.Holds until the vehicle is full.
Full load (all)Holds until every wagon or compartment is full.Holds until the vehicle is full.

The any or all choice only matters for vehicles made of separate wagons or compartments, which in the base game means trains and ships. Any other vehicle, from a truck to a plane, waits for a full load whichever of the two you pick.

Say a train hauls coal wagons and iron ore wagons, with both cargo types set to load at the same stop. On Full load (any) it pulls out as soon as one of the two reaches its percentage, even if the other has hardly started. On Full load (all) it stays until the whole train is loaded.

Why a train set to full load leaves half empty

A full load setting does not hold a vehicle forever. Max. Stop Time still counts down while it loads, and when that time is up the vehicle leaves with whatever it has. That is how a train set to Full load (all) can roll out of the pickup half empty.

The fix is the last step above: Max. Stop Time at ---. If a mixed train still goes part-empty after that, look at the mode, because on Full load (any) it is done once a single cargo type is.

The three time sliders under Departure Configuration

  • Max. Additional Wait. Extra time the vehicle may stand at the stop once loading and unloading are done. The game spends it on keeping the line's vehicles at even gaps.
  • Min. Stop Time. The shortest stay: the vehicle spends at least this long at the stop.
  • Max. Stop Time. The longest stay. If it shows a time, such as 10 min, the vehicle leaves when that time is up, whatever is on board. Pushed all the way right it shows --- instead, which means no limit, so a vehicle on a full load setting waits until it is full.

Where stops are picked and vehicles added is explained in the line manager guide. To know how much a freight train holds before you set its loads, put it together in the train builder.

Why a half-full train unloads nothing at a 50% stop

The percentage set for a cargo at a stop is the share that stays on board when the vehicle leaves, and it is counted on the vehicle's full capacity, not on what it happens to carry. A train that reaches a 50% stop already at half its capacity or less has nothing above that mark, so it unloads nothing there.

A 100-unit train at a 50% stop

Arrives withUnloadsKeeps on board
1005050
803050
50050
40040

Unloading also needs a taker. The cargo only comes off where something within reach of the stop wants it: an industry that processes it, a town district that has asked for it, or a warehouse told to store it. If the line warns that a cargo cannot be unloaded anywhere, the cargo unloading guide finds the stop that is missing its taker.

How to drop part of a load at each stop

  1. At the pickup stop, load the cargo to 100% and make the train leave full: Full load (all), with Max. Stop Time at ---.
  2. At each drop stop, set the same cargo to the percentage that should still be on board after it. To drop 75% of the load there, set 25%.
  3. At the last stop, leave the cargo off the stop's list, and everything still on board comes off there.

Leaving full matters because every drop percentage counts on capacity. A train that set off part-full can reach the first drop stops already under their mark and pass them without unloading.

A warehouse makes a good drop stop when the cargo should wait for another line, as the warehouse guide shows. If the pickup itself will not load, start with the cargo loading checks.

Unload calculator

See what one stop takes off a vehicle, or plan a split over up to four stops for a train that leaves the pickup full.

It unloads 0 and leaves with 40 on board.

Nothing comes off: this stop lets up to 50 stay on board, and the vehicle came in with no more than that.

This counts on something at the stop taking the cargo.

Frequently asked questions

Why does my train leave before it is full in Transport Fever 3?

Either its Max. Stop Time ran out, or it is on Full load (any) and one of its cargo types is already full. A full load setting does not switch that timer off, so drag Max. Stop Time to the far right, where it shows ---; on a train with more than one cargo type, pick Full load (all) as well.

What is the difference between Full load (any) and Full load (all)?

Full load (any) waits until one cargo type is full, Full load (all) until the whole vehicle is. Only trains and ships tell the two apart; for every other vehicle both mean a full load.

How do I make a train wait until it is full?

Choose Full load (all) at the pickup stop and set Max. Stop Time to ---. Without a time limit, the train only departs once every wagon is loaded.

Why does my train not unload at a 50% stop?

Because it came in with half a load or less. The 50% is what may stay on board, measured on the full capacity, so a train already at or under half has nothing to hand over there.

How do I unload only part of the cargo at a stop?

Give that cargo a percentage at the drop stop: the share that should still be on board when the train moves on. A train that left the pickup full and meets a 25% stop leaves three quarters of its load there.

What does --- mean on Max. Stop Time?

No time limit. The slider reads --- once it is pushed all the way right, and a vehicle on a full load setting then waits as long as it takes to fill.

Does Full load (any) work for trucks and buses?

Yes, but it acts exactly like Full load (all) for them. Any vehicle that is not a train or a ship waits to be full with either choice.

Sources

Last checked on November 11, 2026.

Continue reading

A large Transport Fever 3 cargo hub by the sea, with a rail freight yard, trucks, oil tanks and harbor shedsNext stepCargo still on board at the end of the line? Find the stop with nothing to take it.Cargo Type Cannot Be Unloaded? FixWhere each cargo type can be unloaded, which warehouse module it needs, and a step-by-step check for cargo that stays on board.Go there

Related guides